Majority
Headnote
1. Master and Servant (§ 270[1] )—Injuries to Servant—Admissibility of Evidence—Custom.The plaintiff, an employe, of defendants in their factory in this city, was injured while sharpening a small steel drill. The sharpening was done by repeatedly heating and hammering the cutting end of the drill. When sufficiently heated the drill was hammered out on a small slab of steel resting on the end of a bench or table supporting a lathe operated by artificial power and vibrating from the effect thereof. To enable him to hold and manipulate the drill, plaintiff was furnished with a pair of ordinary gas pliers, more or less defective from use. I am satisfied that the judgment was right so far as defendant’s negligence and plaintiff’s absence from contributory negligence are concerned. The only question of any seriousness arises from the admission of testimony.
[ 1 ] One of the questions sharply contested on the trial was the appropriateness of the gas pliers and the steel slab with its uncertain support. Plaintiff contended that the proper implements with which he should have been furnished were a pair of blacksmith’s tongs and a firmly supported anvil. To sustain this contention, testimony was offered in his behalf, tending to show a custom to use these latter devices. Such testimony was proper (Drummond v. Norton, 156 App. Div. 126 , 133, 141 N. Y. Supp. 29 ), and the custom might have been of a limited character, in which case proof of defendants’ knowledge was necessary, or it must have been so general as to have raised a presumption of knowledge on their part. Rickerson v. Hartford Ins. Co., 149 N. Y. 307 , 316, 43 N. E. 856 .
[2-4] Danks, a witness for plaintiff, testified that he had been a button cutter for 13 or 14 years, and had worked for defendants. He had worked in four or five shops in New York City and in Massachusetts shops. He was asked, “Will you state ho'w that [the work of sharpening] was done in other shops?” This was objected to on the ground that: (1) It called for a conclusion; '(2) expert 'testimony for the purpose of showing custom; (3) the witness is not qualified to testify on those subjects. None of these objections was tenable.
[5] The witness then answered that-in the other shops “there was either a man kept specially for that purpose of forging out drills * * * or they had proper tools.” He was then asked, without objection, to describe the method customarily pursued, and he answered, without objection, “There is a blacksmith’s anvil and a blacksmith's tongs.” A sample of such tongs was offered in evidence, and the following question was asked: “Q. Is that the tongs customarily used in this other place you have referred to?
Lane, another witness called by plaintiff, had been a button cutter for 50 years, and had worked in five shops in New York City and vicinity, where it was the custom for the operators to sharpen their own drills. “Q. Do you know the method and the tools that were customarily used for that purpose? A. Certainly. Q. On and prior to the 4th of September, 1912? A. Yes, sir.” After the last answer had been received, the question which had_evoked it was objected to because it did not state whether it referred to any general custom, or only to the custom in shops in which the witness worked. But the form of this question was good, and the preceding question, to. which perhaps the objection was intended to be directed, was equally proper. The only objection to which the latter was open was again the fact that the witness had not specifically sworn to the existence of any custom. But as to this it may be said that if a workman in the trade for 50 years swears that he knows the “custom” pursued in any particular department, presumably there must have been a custom, or he could not know of it. The witness was then asked to state what the custom was. This question was unsuccessfully objected to on the ground, not that there had been no proof that there was any custom, but that it did not appear that the witness was “qualified to state the general custom in the business,” and the witness answered, “Well, the custom is of a man when he is drawing out his drills, these blacksmith’s tongs are kept in the shop for his use and likewise an anvil.” _As I haye said, it was competent for plaintiff to prove a proper custom, but of course it was not competent to prove the practice pursued in particular shops. I do not think, however, that defendants’ objections were directed to this point; they went, rather, to the qualification of the witnesses.
At the conclusion of plaintiff’s case, defendants moved to strike out the testimony of Danks and Lane—
“upon the ground that neither of those witnesses were qualified, * * * to testify as to custom, inasmuch as it appears from the evidence that there are at least 50 shops where this same work is done in New York City alone, and that according to the testimony of Danks, he only knows the instruments and the manner of the work that was done in four or five of these shops, * * * and Lane is familiar only with the manner in which the work is done and the instruments used in five of the shops, and that * * * they cannot possibly be qualified under those circumstances to testify as to the general custom in the business.”
This again goes to qualification, and bases the lack of qualification on inability of the witnesses to testify as to what was done in every
The judgment and order should- be affirmed, with costs.
CLARKE and DOWLING, JJ., concur. INGRAHAM, P. J., and McLaughlin, j., dissent.
Cases cited
- Drummond v. Alfred E. Norton Co. 156 App. Div. 126 at 133, 141 p. 324
- Rickerson v. Hartford Fire Insurance 149 N. Y. 307 at 316, 43 p. 324